Just how do you actually feel about Installing A Bathtub?
Installing a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is also a moderately tough job. If the old bathtub is conveniently accessible, the task can relocate speedily; if you need to open up a wall surface to eliminate the old tub and position the brand-new tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed project, it is far better to think about using one before you start. Chances are you might require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new tub as well as don't need to alter the plan of your previous water pipes.
Your tools as well as product checklist ought to comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of removing the existing faucets can be rather bothersome as a result of the limited gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the required position. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the tub up until the level checks out degree.
To set up taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the supply of water and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise check the overflow outlet and also the normal electrical outlet for leakages.
Finally, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been utilized at the very least when as this will settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to permeate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking time to read our blog. Feel free to take the time to promote this blog posting if you liked it. Many thanks for your time. Don't forget to stop by our website back soon.
Click